Service Manuals, User Guides, Schematic Diagrams or docs for : . Various LCD Panels Panel_SHARP_LK315T3LZ41C_0_[DS]
<< Back | HomeMost service manuals and schematics are PDF files, so You will need Adobre Acrobat Reader to view : Acrobat Download Some of the files are DjVu format. Readers and resources available here : DjVu Resources
For the compressed files, most common are zip and rar. Please, extract files with Your favorite compression software ( WinZip, WinRAR ... ) before viewing. If a document has multiple parts, You should download all, before extracting.
Good luck. Repair on Your own risk. Make sure You know what You are doing.
Image preview - the first page of the document
![Panel_SHARP_LK315T3LZ41C_0_[DS]](/pics/5eb0774c77878.gif)
>> Download Panel_SHARP_LK315T3LZ41C_0_[DS] documenatation <<
Text preview - extract from the document
Global LCD Panel Exchange Center www.panelook.com
LK315T3LZ41C
une 30 7
D 15606C
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
RECORDS OF REVISION
MODEL No. : L315T3LZ41C
SPEC No. : LD-17416
REVISED
DATE NO. PAGE SUMMARY NOTE
No.
2007.04.12 LD-17416 1st Issue
2007.09.28 LD-17416A A P12 Changed Timing characteristics 2nd Issue
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
LD-17416-1
1. Application
This specification applies to the color 31.5" Wide XGA TFT-LCD module LK315T3LZ41C.
* These specification sheets are proprietary products of SHARP CORPORATION ("SHARP") and include materials
protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by
any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of
SHARP.
* In case of using the device for applications such as control and safety equipment for transportation (aircraft, trains,
automobiles, etc.), rescue and security equipment and various safety related equipment which require higher
reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant
system design should be taken.
* Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications,
telecommunication equipment (trunk lines), nuclear power control equipment and medical or other equipment for
life support.
* SHARP assumes no responsibility for any damage resulting from the use of the device that does not comply with
the instructions and the precautions specified in these specification sheets.
* Contact and consult with a SHARP sales representative for any questions about this device.
2. Overview
This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is
composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit, inverter circuit and back light
system etc. Graphics and texts can be displayed on a 1366 RGB 768 dots panel with 16,777,216 colors by
using LVDS (Low Voltage Differential Signaling) to interface, +5V of DC supply voltages.
This module also includes the DC/AC inverter to drive the CCFT. (+24V of DC supply voltage)
And in order to improve the response time of LCD, this module applies the Over Shoot driving (O/S driving)
technology for the control circuit .In the O/S driving technology, signals are being applied to the Liquid Crystal
according to a pre-fixed process as an image signal of the present frame when a difference is found between image
signal of the previous frame and that of the current frame after comparing them.
By using the captioned process, the image signals of this LCD module are being set so that image response can be
completed within one frame, as a result, image blur can be improved and clear image performance can be realized.
3. Mechanical Specifications
Parameter Specifications Unit
80.04 Diagonal cm
Display size
31.5 Diagonal inch
Active area 697.69 (H) x 392.26 (V) mm
1366 (H) x 768 (V)
Pixel Format pixel
1pixel = R + G + B dot
Pixel pitch 0.51075(H) x 0.51075 (V) mm
Pixel configuration R, G, B vertical stripe
Display mode Normally black
Unit Outline Dimensions (*1) 780.0(W) x 450.0(H) x 51.0(D) mm
Mass 6.4 0.3 kg
Anti glare, low reflection coating
Surface treatment Hard coating: 2H
Haze: 23 +/- 5%
(*1) Outline dimensions are shown in Fig.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
LD-17416-2
4. Input Terminals
4-1. TFT panel driving
CN1 (Interface signals and +5V DC power supply) (Shown in Fig.1)
Using connector FI-X30SSL-HF (Japan Aviation Electronics Ind. , Ltd.) or equivalent
Mating connector FI-X30H, FI-X30C or FI-X30M (Japan Aviation Electronics Ind. , Ltd.)
Mating LVDS transmitter THC63LVDM83A or equivalent device
Pin No. Symbol Function Remark
1 VCC +5V Power Supply
2 VCC +5V Power Supply
3 VCC +5V Power Supply
4 VCC +5V Power Supply
5 GND GND
6 GND GND
7 GND GND
8 GND GND
Pull up
9 SELLVDS Select LVDS data order Note 1
Default H:3.3V
10 NC
11 GND Ground
12 RIN0- Negative (-) LVDS differential data input LVDS
13 RIN0+ Positive (+) LVDS differential data input LVDS
14 GND Ground
15 RIN1- Negative (-) LVDS differential data input LVDS
16 RIN1+ Positive (+) LVDS differential data input LVDS
17 GND Ground
18 RIN2- Negative (-) LVDS differential data input LVDS
19 RIN2+ Positive (+) LVDS differential data input LVDS
20 GND Ground
21 CLKIN- Clock Signal(-) LVDS
22 CLKIN+ Clock Signal(+) LVDS
23 GND Ground
24 RIN3- Negative (-) LVDS differential data input LVDS
25 RIN3+ Positive (+) LVDS differential data input LVDS
26 GND Ground
Pull down
27 R/L Horizontal shift direction Note 2
Default L:GND
Pull down
28 U/D Vertical shift direction Note 2
Default L:GND
29 Reserved Not Available
30 Reserved Not Available
note GND of a liquid crystal panel drive part has connected with a module chassis.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
LD-17416-3
Note1 SELLVDS
Transmitter SELLVDS
Pin No Data =L(GND) =H(3.3V) or Open
51 TA0 R0(LSB) R2
52 TA1 R1 R3
54 TA2 R2 R4
55 TA3 R3 R5
56 TA4 R4 R6
3 TA5 R5 R7(MSB)
4 TA6 G0(LSB) G2
6 TB0 G1 G3
7 TB1 G2 G4
11 TB2 G3 G5
12 TB3 G4 G6
14 TB4 G5 G7(MSB)
15 TB5 B0(LSB) B2
19 TB6 B1 B3
20 TC0 B2 B4
22 TC1 B3 B5
23 TC2 B4 B6
24 TC3 B5 B7(MSB)
27 TC4 NA NA
28 TC5 NA NA
30 TC6 DE(*) DE(*)
50 TD0 R6 R0(LSB)
2 TD1 R7(MSB) R1
8 TD2 G6 G0(LSB)
10 TD3 G7(MSB) G1
16 TD4 B6 B0(LSB)
18 TD5 B7(MSB) B1
25 TD6 NA NA
NA: Not Available
(*) Since the display position is prescribed by the rise of DE (Display Enable) signal,
please do not fix DE signal during operation at "High."
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
LD-17416-4
Note 2 Display reversal function
Normal (Default) Horizontal reverse image
:
Vertical reverse image Horizontal and vertical reverse image
: :
Interface block diagram
Corresponding Transmitter: THC63LVDM83R (THine) or equivalent device
side
(TFT - LCD side)
8 Rx1IN0+(13)
G0 G7
8
8 Rx1IN0-(12) R0 R7
R0 R7
Rx1IN1+(16) 8
8 G0 G7
B0 B7
LVDS 8
Rx1IN1-(15) TTL B0 B7
Internal circuits
Rx1IN2+(19)
Rx1IN2-(18)
TTL
LVDS
Rx1IN3+(25)
ENAB
Rx1IN3-(24) ENAB
Rx1CLKIN+(22)
controller
CLK PLL PLL
Rx1CLKIN-(21) CK
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
LD- 17416-5
Block Diagram (LCD Module)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
LD- 17416-6
SELLVDS= High (3.3V) or Open
1 cycle
CKAIN+
CKAIN-
RIN0+ R3 R2 G2 R7 R6 R5 R4 R3 R2 G2
RIN0-
RIN1+
G4 G3 B3 B2 G7 G6 G5 G4 G3 B3
RIN1-
RIN2+ B5 B4 DE NA NA B7 B6 B5 B4 DE
RIN2-
RIN3+
R1 R0 NA B1 B0 G1 G0 R1 R0 NA
RIN3
SELLVDS= Low(GND)
1 cycle
CKIN+
CKIN-
RIN0+ R1 R0 G0 R5 R4 R3 R2 R1 R0 G0
RIN0-
RIN1+
G2 G1 B1 B0 G5 G4 G3 G2 G1 B1
RIN1-
RIN2+ B3 B2 DE NA NA B5 B4 B3 B2 DE
RIN2-
RIN3+ R7 R6 NA B7 B6 G7 G6 R7 R6 NA
RIN3-
DE: Display Enable
NA: Not Available (Fixed Low)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
LD- 17416-7
4.3. Backlight driving
CN4 (+24V DC power supply and inverter control)
Using connector: S14B-PH-K-S (LF) (JST)
Mating connector: PHR-14 (JST)
Pin No. Symbol Function Default(OPEN) Input Impedance Remark
1 VINV +24V -
2 VINV +24V -
3 VINV +24V -
4 VINV +24V -
5 VINV +24V -
6 GND -
7 GND -
8 GND -
9 GND -
10 GND -
11 Reserved For LCD module internal
usage, should be open
12 VON Inverter ON/OFF GND : pull down 22K ohm [Note 1]
Inverter OFF
13 VBRT Brightness Control 3.3V : pull up 100K ohm [Note 3]
Brightness 100%
14 VBRT_ sel Brightness Control 3.3V : pull up 100K ohm [Note 2]
selection Selected Analog PWM
*GND of an inverter board is not connected to GND of a module chassis and a liquid crystal panel drive part.
[Note 1] Inverter ON/OFF
Input voltage Function
0V Inverter : OFF
3.3V Inverter : ON
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
LD- 17416-8
4-3. The back light system characteristics
The back light system is direct type with 18 CCFTs (Cold Cathode Fluorescent Tube).
The characteristics of the lamp are shown in the following table.
The value mentioned below is at the case of one CCFT.
Item Symbol Min. Typ. Max. Unit Remarks
Life time TL 60000 - - Hour Note
Note Lamp life time is defined as the time when brightness becomes 50% of the original value in the
continuous operation under the condition of Ta=25 and brightness control(VBRT=0V).
This definition is valid with the condition that the module is placed horizontally. (The wide side of the
module should be parallel to the ground.)
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
LD- 17416-9
5. Absolute Maximum Ratings
Parameter Symbol Condition Ratings Unit Remark
Input voltage
VI Ta=25 -0.3 ~ 3.6 V Note 1
(for Control)
5V supply voltage
VCC Ta=25 0~+6 V
(for Control)
Input voltage VBRT
Ta=25 0~+6 V
(for Inverter) VON
24V supply voltage
VINV Ta=25 0 ~ +29 V
(for Inverter)
Storage temperature Tstg - -25 ~ +60
Note 2
Operation temperature
Topa - 0 ~ +50
(Ambient)
Note 1 SELLVDS, R/L, U/D,TEST, Frame, O/S set, Temp1, Temp2, Temp3
Note 2 Humidity 95%RH Max.(Ta 40 )
Maximum wet-bulb temperature at 39 or less.(Ta>40 )
No condensation.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
LD- 17416-10
6. Electrical Characteristics
6-1. Control circuit driving Ta=25
Parameter Symbol Min. Typ. Max. Uniit Remark
Supply voltage Vcc +4.5 +5.0 +5.5 V Note 1
+5V supply
voltage Current Icc Note 2
- 800 1800 mA
dissipation
Permissible input ripple VRP Vcc = +5.0V
- - 100 mVP-P
voltage
Differential input High VTH - - 100 mV VCM = +1.2V
threshold voltage Low VTL -100 - - mV Note 6
Input Low voltage VIL - - 0.7 V
Note 3
Input High voltage VIH 2.6 - 3.3 V
VI = 0V
IIL1 - - 100 A
Note 4
Input leak current (Low)
VI = 0V
IIL2 - - 400 A
Note 5
VI =3.3V
IIH1 - - 100 A
Note 4
Input leak current (High)
VI =3.3V
IIH2 - - 400 A
Note 5
Terminal resistor RT - 100 - Differential input
Note VCM: Common mode voltage of LVDS driver.
Note 1
Input voltage sequences Dip conditions for supply voltage
0 < t1 10ms a) 2.7V Vcc < 4.5V
10ms t2-1 20ms td 10ms
t2-2 10ms b) Vcc < 2.7V
0 < t3 1s Dip conditions for supply voltage is
t4 1s based on input voltage sequence.
t5 200ms
0.9VCC
0.9Vcc
0.1Vcc 0.1Vcc
Vcc 0.1Vcc
t2-1
t4
t1 t3
Data1
t2-2
Data2
t5 ON
Back light:Vinv OFF OFF
ata1:CLKIN ,RIN0 ,RIN1 , RIN2 , RIN3
ata2:R/L,U/D,SELLVDS,Frame,O/Sset,Temp1,2,3
About the relation between data input and back light lighting, please base on the above-mentioned input
sequence.
When back light is switched on before panel operation or after a panel operation stop, it may not display
normally. But this phenomenon is not based on change of an incoming signal, and does not give damage to a
liquid crystal display.
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
LD- 17416-11
Note 2 Typical current situation: 256 gray-bar pattern (Vcc = +5.0V)
The explanation of RGB gray scale is seen in section 8.
Vcc 5.0V
CK 82.0MHz
Th 20.67 s
Note 3 R/L, U/D, SELLVDS, TEST, Frame, O/S set, Temp1, Temp2, Temp3
Note 4 R/L, U/D
Note 5 SELLVDS, TEST, Frame, O/S set, Temp1, Temp2, Temp3
Note 6 CKIN+/CKIN-, RIN0+/RIN0-, RIN1+/RIN1-, RIN2+/RIN2-, RIN3+/RIN3-,
6-2. Inverter driving for back light
The back light system is direct type with 18 CCFTs (Cold Cathode Fluorescent Tube). Ta=25
Parameter Symbol Min. Typ. Max. Unit Remark
Current dissipation IINV - 4.2 6.5 A VINV = 24V
24V VBRT = 0V, VON=5V
Supply voltage VINV 22.5 24.0 25.5 V Note 1
Permissible input ripple
VRF - - 200 mVp-p VINV = +24V
voltage
Input voltage (Low) VONL 0 - 1.0 V Von
Input voltage (High) VONH 3.0 5.0 6.0 V impedance=24k
VBRT
Brightness control voltage VBRT 0 5.0 V
impedance=100k
Note 1 1)VINV-turn-on condition
0.9VINV T1 100s
T2 1ms
0.1VINV
VINV
T1 T2
VON,VBRT 0V 0.1VON
2) VINV-turn-off condition
VON,VBRT t1 1ms
t1
1.0V 0V
VINV
0.9VINV
0V
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
LD- 17416-12
7. Timing characteristics of input signals
7-1. Timing characteristics A
Timing diagrams of input signal are shown in Fig.2
Parameter Symbol Min. Typ. Max. Unit Remark
Clock Frequency 1/Tc 65 82 85 MHz
1560 1696 1940 clock
Horizontal period TH
20.20 20.67 - s
Data enable
Horizontal period (High) THd 1366 1366 1366 clock
signal
Vertical period TV 778 806 972 line
Vertical period (High) TVd 768 768 768 line
Note When vertical period is very long, flicker and etc. may occur.
Please turn off the module after it shows the black screen.
Please make sure that length of vertical period should become of an integral
multiple of horizontal length of period. Otherwise, the screen may not display properly.
TH
THd
1366 1 2 1366
Tc
1 2 767 768
TVd
TV
Fig.2 Timing characteristics of input signals
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
LD- 17416-13
7-2. Input data signal and display position on the screen
R1 G1 B1 R2 G2 B2
R G B
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
Global LCD Panel Exchange Center www.panelook.com
LD- 17416-14
8. Input Signal, Basic Display Colors and Gray Scale of Each Color
Data signal
Colors &
Gray R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7
Gray scale
Scale
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Green 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Basic Color
Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Red 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Black GS0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
◦ Jabse Service Manual Search 2026 ◦ Jabse Pravopis ◦ onTap.bg ◦ Other service manual resources online : Fixya ◦ eServiceinfo